Programmable User Options Several user programmable options are available via user codes 1, 2 or 3. Select characters from the list below: Continue until you have entered eight characters. The display will show: The display will show for example: Text is entered in a similar way that you would enter text on a mobile telephone.
User Manual for Eurosec PR5208 Domestic Intruder Alarm Programming User Codes Up to nine user codes may be programmed on predetermined levels.
Re-setting the display after a Mains Fail If the system has been programmed for Any code reset With the display showing: Enter your User code Then press Reset. Pressing the Quick key during exit will shorten the exit time to 3 seconds. Setting the system with Mains Fail In the event of a short term power cut, where it is known when power will be restored, e. Tamper Resetting With the display showing: Enter a valid User code. If Anti has been programmed for Alarm Reset, contact the Central Station or Engineer, as instructed by the Installation Company and quote the number given by the display. If Alarm Reset has been programmed for Master, then the display will show, for example, each time the User attempts to set!
If a Master Code Reset has been programmed by the engineer, a higher level of code will be required. Your installation company will have informed you as to the type of reset that your system is set for. Your installation company will have programmed the reset modes for your system so that it complies with your insurance company and legislation requirements. Resetting After an Alarm After an alarm the system needs to be reset. If an alarm occurs when the system is set, the cause of the alarm will be displayed for 10 seconds after you unset the system. Proceed to the keypad and enter a valid User Code. Enter the premises via an authorised Entry Point. Enter a valid User Code followed by 2 or 3. Part 2 is a second set of zones that may be omitted and Part 3 will combine Part 1 and Part 2. Two other Part Sets may be available for your system. The display will show, for example: Part Setting the System using Part 2 or 3. At the start of the setting procedure, a fault Exit Now! Eurosec CP8L User ManualĮxit the premises via an authorised exit route. After checking the premises are secure: Enter a valid User Code followed by. The bottom line of the display will then be blanked off.įull Setting the System. Set or Unset Status will only be displayed for ten seconds when the system is Set or Unset. Throughout this manual, reference will be made to the Master User Code, the factory set default is Display Status Blanking Depending on Control Panel installed, it may be a requirement that the Status Set or Unset display of the security system is not displayed. Several user programmable options are available that will be covered later in this manual. Your installation company will have programmed your system to protect your premises to the highest possible standards. Introduction Welcome to the eurosec control panel. View and Download Eurosec CP8L user manual online. Wire the LCD RKP as shown in the wiring section of this manual. The eurosec control panel is supplied as a blank fronted end station. Is the 'Risco Gardtec Eurosec LCD Keypad' product that you sell the right one, or do i need the other one you sell that is for CPX and GTag? Also the original company to fit the system are no longer around, would you have a copy of the installer manual with the default master/installer code as i quite expect that taking the old pad off the wall will set off the system and as the buttons dont work i'll need to reset it all.Throughout this manual refer- ence will be made to the User Code, the factory set default is This code is programmable along with eight other User Codes.
Galaxy user guide video how to program a user code duration 1 24 cia christie intruder alarms ltd 8 861 views, eurosec pr5208 rev1 0 user manual - download. Gardtec-eurosec-cpx-engineer-manual.pdf 2015.
Version pdf for eurosec pr5208 engineer manual using the link below. Free access for PDF Eurosec burglar alarm instructions.pdf.
Read and Download eurosec pr5208 rev1.0 user manual. Cardiff Office Lamby Workshops Lamby Way Cardiff.Įurosec Alarm Manual 5208.
Notorious Big Full Discography Torrent Download. Head Office 35 Phoenix Business Park Telford Street Newport NP19 0LW. The keys 2 & 5 have given up working, so we need to replace just the keypad. I have a client who has an existing alarm system with a eurosec keypad, PR5208 rev 1.0.